Boat Outfitting - Tools

.75" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter....

1.5" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over...

Stainless Steel Standoff 1.25" Base 1/4" x 20 Thread .75" Tall - 6-PackUnlike the SOB standoffs which have a blind thread, the SOT series standoffshave a thread which runs all the way through the barrel of the standoff.This allows the standoff to be mounted...

.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide...

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded...

No Slide Metal/Composite BonderRevolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based,...

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is...

1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide...

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops...

Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges (sold separately) When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long...

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength...

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Rigging Knife - 304 Stainless SteelThis handy Rigging Knife includes a sharp blade, Marlin spike, shackle key, screw driver, bottle opener, and a loop to attach a lanyard (not included). Constructed of corrosion resistant 304 stainless steel. A great addition to any tool box....

Plastic Suction Cup HandleInjection Molded Nylon/Nitrile-Buna Rubber Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat...